Chapter 6
Loops, markers and the waveform
Up to three named loops, named markers, and the waveform that helps you place them.
Loops and markers are for the hard parts of a song. A loop repeats one stretch of the song over and over, so you can practice it. A marker is a named spot you can jump to, such as "Verse 2" or "Bridge". Both are saved with the song, and the waveform on the seek bar helps you place them exactly.
Loops and markers need the trial or a license. In the free version their buttons tell you so.
The A-B loop
A loop has a start, A, and an end, B. While the loop is on, the song plays from A to B and goes back to A.
- Play the song. When you hear the spot where the loop should start, click Set A ([).
- When you hear the spot where it should end, click Set B (]). The loop turns on and the song repeats from A to B.
- To stop looping and play on, click Loop Off (L). The same button turns it on again, so A and B are not lost.
- Clear (Ctrl+L) takes out A and B.
The time of A and B shows beside their buttons. A and B are kept to a tenth of a second, and they can never be closer than 2 seconds. A key or drag that would break that does nothing, or stops at the limit.
Fine-tuning A and B
- The small arrows beside each time move that end 0.1 second earlier or later. Holding a button repeats.
- On the seek bar, drag the A or B tab to move that end. Drag between the two tabs to move the whole loop and keep its length.
- Alt+Left and Alt+Right move the whole loop earlier or later, 0.1 second at a time (faster when held). It stops at the ends of the song and at the neighbor loops.
- Setting A after B starts a fresh loop (the old B was behind you, so it goes). Setting A or B too close to the other end is ignored.
Getting to the loop
- Jump to A (1) moves to the start of the loop and turns the loop on. A playing song carries on playing from A, and a paused one stays paused. It needs both A and B to be set.
- Clicking a loop's A or B tab on the seek bar also turns the loop on.
- Stop (S) inside a loop returns to A instead of the start of the song, and so does the end of a song while the loop is on. A countdown before the loop (the "Pause between loop repeats" setting in Options) is covered in Playing a song.
Up to three loops
A song can have up to three loops, for example a verse, a chorus and a bridge. The player shows as many loop boxes as the song has. You can have all the loops on at the same time. If you click past one loop, the song plays on into the next loop and stays in it until you do something to change that. After the last loop, the song plays on to the end.
- Start loop 2 (and Start loop 3) on the first box opens another box. Set its A and B the same way. The button is greyed out when the song has no room left for another loop of at least 2 seconds, and its tooltip says why.
- Loops never overlap, and they keep 0.2 second apart. A loop edit that would run into another loop is refused (with a short notice), and drags and nudges stop at the neighbor.
- Remove on the second and third boxes deletes that loop. The loops after it move up. Loop 1 can be cleared but never removed.
- Drag the grip at the left of a box title to change the order of the loops. It shows when the song has two or more loops. Alt+Up and Alt+Down do the same for the active loop. The order is yours; it does not have to follow the order in the song.
- The keys [, ], L, Ctrl+L, 1 and Stop act on the loop the song is inside, or otherwise on the active loop: the one you last clicked or set, or the one the playing song went into. Each box also has its own buttons.
Naming a loop
Double-click the title of a box, or press F2 (for the active loop), and type a name of up to 20 characters. Enter saves it and Esc cancels. An empty name goes back to the number. The name shows in the box, in tooltips, and in the file names that Export to File makes.
Saved with the song
The loops of a song are saved with it. When you open the song again the loops are there, but turned off, so the song plays from the start unless you turn one on. A saved loop that is too short, or overlaps another, is dropped.
The waveform
Check Waveform (at the right of the seek bar; W). The seek bar becomes taller and shows the shape of the song, with its quiet and loud parts. Choruses and pauses are easy to see, so it is much easier to put a loop end or a marker in the right place. The choice is remembered.
- The first time a song is opened with the waveform on, the program draws the wave in the background. It is kept, so the next time it is quick.
- The slider at the right end of the seek bar sets how tall the wave is, up to three times normal. Click it, then Up and Down move it (Home is normal height and End is the tallest), or use the mouse wheel over it.
- Clicking the seek bar still moves the playhead there, with or without the waveform.
Markers
While the song plays, click Add Marker (K). A marker is added at the spot you are hearing and named "Marker 1", "Marker 2" and so on. A small triangle for it shows on the seek bar.
- A song can have up to 50 markers. They are kept to a tenth of a second and at least 2 seconds apart (more in a long song, because the triangles need room). A marker that is too close to another is refused, with a notice that names the one it is too close to.
- Click a triangle to jump to that marker. Playback > Loop > Previous Marker (, comma) jumps to the previous marker and Next Marker (. period) to the next. Right after a marker, comma goes back to the one before it. A playing song carries on from the new spot; a paused song stays paused.
- Drag a triangle to move the marker. It stops at its neighbors.
- Right-click a triangle for Rename marker... or Delete marker. A name can be up to 50 characters.
- With the waveform on, check Marker lines to draw a thin line through the wave at each marker, so you can line a marker up on the wave. The setting stays as you set it, song after song.
The Markers window
The first marker adds a Markers check box at the right of the seek bar. Check it (Ctrl+K), or choose Playback > Markers Window, to open the window. Adding a marker never opens it by itself.
- The list shows each marker with its time. Go (Enter, or a double-click) jumps to the highlighted marker.
- Rename (F2) renames it. Delete removes the highlighted markers (one is deleted at once; several ask first). Clear All deletes every marker of the song, after asking.
- Add Marker (K) adds one, and the window shows it as you go.
- An empty list says "No markers yet." and reminds you that K adds one.
- The window floats until you drag it against the left or right edge of the main window: it docks there, and drags away to float again. It remembers where it was (docked at the left at first).
Markers are saved with the song.